USD
GSK928TEa/GSK928TD-L Alarm List
GSK928TEa/GSK928TD-L Alarm List
| Alarm Table in JOG OR AUTO Working Mode (i.e.E300~ E499) | |||
| The Alarm type in JOG and AUTO is divided to: Alarm in executing relative operation and The relative | |||
| Alarm in executing statement two kinds | |||
| Programming Chapter Eight Alarm Message | |||
| 8.5.1 Alarm in Executing Relative Operations (i.e E300~E399) | |||
| Alarm number |
Alarm prompt | Alarm reason | Troubleshooting |
| E302 | Z driver unit alam |
Z drive unit alam | CheckZ axis drive unit, resolve the failure to power-on again |
| E303 | x driver unit alarm |
X drive unit alarm | Check t X axis drive unit, resolve the failure to power-onagain |
| E304 | Y driver unit alarm |
Y drive unit alarm | Check Y axis drive unit, resolve the filure to power-on again |
| E305 | Positive hardware limit alarm |
XorZ positive limit swichis closed | Xor z negatively moves in JOG working l the alarm is releasec mode |
| E306 | Negative hardware imit alarm |
XorZ negative limit switch is closed | Xor Z positively moves in JOG working mode tll the alarm is released |
| E307 | z machine (+) software limit alam |
Z machine coordinate(Zm) exceeds the positive software limit alam value (P015) |
Xor Z positively moves in JOG working mode, or set the machine coordinate to zero again, release the alam |
| E308 | xmachine (+) software limit alam |
X machine coordinate(Zm) exceeds the positive software limit alam value(P017) |
Xnegatively .moves in JOG working mode, or set the machine coordinate to zero again, release the alarm |
| E309 | Y machine (+) software limit alarm |
Y machine coordinate(Zm) exceeds the positive software limit alam Value(P019) |
Y negatively moves in JOG working mode, or set the machine coordinate to leasethealam zero again, release the alam |
| E310 | Z machine (-) software limit alam |
Xmachine coordinate(Zm) exceeds the negative software limit alarm value(P016) |
Z positively moves in JOG working mode, or set the machine coordinate to zero again, release the alam |
| E311 | x . machine () software limit alarm |
x machine coordinate(Zm) exceeds the negative software limit alarm value(P018) |
X positively moves in JOG working mode, or set the machine coordinate to zero again, release the alam |
| E312 | Y machine () software limit alarm |
Y machine coordinate(Zm) exceeds the negative software limit alarm value(P020) |
Y positively moves in JOG working mode, or set the machine coordinate/machine zero retum again, release the alarm |
| E313 | nose (+) limit software alam |
Z tool nose coordinate exceeds the posive limit alam value(P009) |
Z negativel moves in JOG working mode, or execute the toltn/programn reference point retum again, release the alarm |
| E314 | X nose (+)sofware limit alarm |
X tool nose coordinate exceeds the positive limit alam value(P011) |
文axis negatively moves in JOG working mode, or execute the toltinprogram reference point retum again, release the alarm |
| E315 | Y nose software imit alarm |
Y tool nose coordinate exceeds the positive limit alam value(P013) |
Ynegatively moves in JOG working mode, or execute the toltn/rogram reference point returm again, release the alarm |
| E316 | E316: Z nose (-)software limit alam |
Z tool nose coordinate exceeds the negative limit alam value(P010) |
Y positively moves in JOG working mode, or execute the toettin/program reference point returm again, release the alarm |
| E317 | X nose (-)software limit alarm |
X tool nose coordinate exceeds the negative limit alarm value(P012) |
x positively moves in JOG Wworking mode, or execute. the tolttn/program reference point retum again, release the alarm |
| E318 | E318:Y nose (-) software limit alarm |
Ytool nose coordinate exceeds the negative limit alarm value(P014) |
Y positively moves in JOG working mode, or execute the toletting/program reference point retum again, release the alam心POS |
| E319 | Output frequency too high |
ZIXY pulse output frequency exceeds the system speaied ran ge |
Reduce the moving speedor modify the pulse multiplication ratio, division Ceoffcient(P203, P204) to the proper value |
| 271 | |||
| Manual Alarm Alarm prompt Alarm reason Troubleshooting number |
|||
| E320 | Thread spindle speed too high |
the value of spindle speed multiplying the thread pitch(P) is more than max. speed limit of cutting feed (P113) |
Reduce the feedrate or modify P113 value to the enough |
| E321 | Can't execute G32 in DRY |
The system cannot execute G32 in DRY RUN working mode |
Deleted G32, then execute the programin DRY RUN working mode |
| E322 | G34: Screw pitch is out of range |
In machining the thread, the pitchis grading, it will exceed the system specified range before the end point. |
Modify the machining program |
| E330 | Tool lock signal does not use |
The settoolpost typeneed the clamping signail. but the parameter P408_d6 doesn'tetitto be the clamping signal |
Set P408 _d6 to be the using tool post clamping signal |
| E331 | Chuck release P507 not define |
The system has not defined the tool post using releasing signal (P507) |
Set the parameter P507 to be the corresponding interface signal |
| E332 | Chuck in-position P508 not define |
The system has not defined the tool pot in-position using signal(P508) |
Set the parameter P508 to be the corresponding interface signal |
| E333 | Tool-post gating P529 not define |
The system has not defined the tool selection using strobesignal (P529) |
Set the parameter P529 to be the corresponding interface signal |
| E334 | Tool-post locking is overtime |
In tool post rotation(CCW) time in tool change, it can't inspect the tool post champing signal |
Check the tool post champing signal is in normal or not, or delay the reversion time(P324) |
| E335 | Tool-post NO alarm |
Atter tool change completed, thetool selection number isn't the target number |
Check the target tool selection signalisin nomal or not |
| E336 | No changing tool | The parameter set the too changing forbidden |
Modity the forbidden tool changing parameter P403 d7 |
| E337 | Detect tool post signal overtime |
In tool post rotation (CCW) time in tool change, it can't inspect the tool selection number |
Check the target tool selection signalisin normal or not, or delay the time for tool changing in property |
| E338 | Chuck doesn't clamp, no spindle |
Forbid staring the spindle when the Chuck. s. rleased in spindie and chuck locking each other |
Execute the chuck damping oerainto clamp the workpiece |
| E339 | Spindle doesn't stop, no chuck |
When ! the . spindle and chuck are locking each other, don't operate the spindle without stopped the spindle |
Stop the spindle, then operate the chuck |
| E340 | Forbid function of chuck |
The parameterhassettoforbid control chuck |
Modify parameter P409 _d7 |
| E341 | Spindle doesn't stop, no tail |
" When the spindle and chuck are , locking each other, don't operate the tailstock without stopped the spindle |
Stop the spindle, the operate the tailstock |
| E342 | Forbid function of tail stock |
The parameter has set to forbid controlthet ailstock |
Modily the parameter P409 _d4 |
| E343 | M10 no respond | r The system cannot check the valid ! chuck champing selection signal RM11 in contolling chuck champing |
Check the chuck damp selection signalis in nommal or not |
| E344 | M11 no respond | The system cannot check the valid chuck releasing selection signal RM11 in controlling chuck releasing |
Check the chuck releasing selection signal is in normal or not |
| E345 | M78 norespond | the system cannot check the valid tailstock going-forward in-position signal RM78 in contolling taistock going-forward |
Check the tailstock signal is in normalor not |
| E346 | M79 no respond | The system cannot check the valid tailstock going backward in-position signal alarm 79 in contolling tailstock _going backward |
Check the tailstock going backward signal is in normal or not |
| E347 | The non-frequency spindle |
The system can't execute the constant surface speed command G96 or gear shifing command M41-M44 in non-frequency spindle |
Modify the spindle ollocated parameter P410 d6 |
| Alarm number |
Alarm prompt | Alarm reason | Troubleshooting |
| E348 | The program isnot ready |
Program error, execution is forbidden | Modiy the program, resolve error |
| E349 | Use [ return machine zero] key |
When the machineis back to zero function, the mdiying manual is forbidden |
Using “MACHINE ZERO RETURN key to zero |
| E350 | S exceed limit | The Sxxx value exceeds the gear shiting range in the non-frequency spindile gear shifing |
Modity the S value to the correct gear value |
| 「 E351 | Spindle is Cntrolede by Y axis |
Whenthespindleiscontrlledby Y axis. the stant and stoo of the spndile can't be controlled in JoG |
ExecteMa8&togetbackthespindle function |
| E352 | Spindle Y, levels can't be changed |
The spindle can't execute the gear shifting. command when is controlled by Y axis |
Execute M48 to get back the spindle function |
| E353 | M47/M48 function doesn't work |
The M47M48 function forbidden is set in parameter when thereisno Y axis(P405_ d1) or Y axis can't be changed (P410 d4) |
Modify parameter P405_ d1 andP410 _d4 |
| E354 | Spindle doesn't stop, no M47/M48 |
The M47/M48 is forbidden to execute when the spindle don't stop |
Stop the spindle, then execute M47/M48 |
| E355 | 254 program error | 254 program error, the machining program is forbidden to execute |
Modify 254 program, resolve error |
| E357 | Feeding override is 0 |
The overnide is zero in feedrate | Adjusted to feedrate overide nonzero |
| E358 | Spindle running is abnormal . |
The spindle rotate speed is checked to be zero after the spindle is started |
Check the spindle relative part, resolve the error or modify parameter P402 d6 to forbid its function |
| E359 | Alarm: pressure is low. |
,The systemhaschecked thelow pressure and lasted the parameter P332 specified time |
Check the hydraulic pressure equipment, resolve the error |
| E360 | Alarm: protecting door isn't closed |
The safty door don't close inAUTO | Close the safety door |
| E361 | Material convey alarm |
The system has checked it's out of rod in M20, automatism stop alam |
Change the rod, then go on the machining |
| E362 | Lubricating doesn't start |
The system executes the M32/M33 command without lubricating function |
Set the parameter P506 to be the corresponding lubricating control interface |
| E363 | E363: Tool NO exceeds limit |
The target tool number exceeds the parameter P319 specified value in changing tool |
Modify tool number or modify P319 tobe the maxima system I tool number |
| E364 | Tool post release overtime |
Thetoolpose champing signal is effective always in tooil changing and releasing tool post |
Check the tool pose champing signal and resolve error |
| E365 | Y axis is speed control mode |
The spindle and Y axis allow change(P410_ d4), but the system don't allow to control the Y axis moving in current spindle non-position control mode |
Execute M47 first, change the spindle to location control mode |
| E366 | Clamp in-position signal abnormal |
When the ollowing chuck respond signal checking alam function is open, the chuck champing in-position signal is invalidation |
Control the chuck champing again or resolve the chuck error |
| E367 | Release in-position signal abnormal |
When the ollowing chuck respond signal checking alam function is open, the chuck champing in-position signal is invalidation |
Control the chuck champing again or resolve the chuck error |
| E368 | Tail stock FW signal abnormal |
When the fllowing tailstock respond signal checking alam function is open, the tailstock going-forward in-position signal is invalidation |
Control the tailstock going foward again or resolve the chuck error |
| [ E369 | [ Tail stock BK | When the fllowing tailstock respond | Control the tailstock going backward |
| Manual | |||
| Alarm number |
Alarm prompt | Alarm reason | Troubleshooting |
| signal abnormal | signal checking alam function is open, the tailstock going backward in-position signal is invalidation |
again or resolve the chuck error | |
| E370 | P319 and P320 are not equal |
T panter soting P3194P3200 tool changing, the position parameter P408 d7=0 |
Sel he prameler P408 d7-01 againar letP319 equal to P320 |
| E371 | External start signal abnormal |
The outside starting key always isn't released when the system changes toJOG or AUTO working mode |
Check the outside startup signal and resolve the error |
| E372 | Chuck foot switch signal abnormal |
The chuck foot switch always isn't released when the system changes toJOG or AUTO working mode |
Check the chuck foot switch signal and resolve the error |
| E373 | Tall foot switch signal abnormal |
The tailstock foot switch always isnt released when the system changes to JOG or AUTO working mode |
Check the tilstock foot switch signal and resolve the error |
| E374 | G31 monitor interface undefined |
The parameter P532 is undefined(G31 input checking) |
Define the P532 to be G31 checking input pin |
| E375 | Spindle doesn't stop |
When the system is in the tappingin JOG working mode, the spindle doesn't stop or the rotate speed isn't zero |
It's llowed to enter the tapping in JOG working mode when the spindle has stopped and the rotate speed is zero |
| E376 | Manual tapping speed is too high |
The manual tapping rotate speedis too fast |
Reduce the tapping rotate speed in properly |
| E377 | Commands have been undefined |
Used the undefined command M60-M74 |
Modify the program |
| 8.5.2 Relative alarm in executing statement (i.e.E400~ E499) Alarm in statement program means in the program by statement, the alarm is made by the wrong statement command in executing the workpiece program, the alarm can be resolved by inputting the correct command. |
|||
| Alarm number |
Alarm prompt . |
Alarm reason | Troubleshooting |
| E400 | Monitor variable not initialize |
The system doesn't evaluate and set the judgement condition to the process monitor before startup |
Modify program, put right |
| E401 | In macro, divisor isO |
The divisor is zero in statement operation |
Modify the divisor in macro command, letit don't be zero |
| E402 | not support monitor calculation |
The process monitor assignment tatement has assignment operation which is not supportedby the system, ie. square root, sine operation |
Modily program, put right |
| E403 | r5008 data error | Evaluate the variable r5008 llegal value |
Modify program, put right |
| E404 | Variable data r6xx error |
llgaily used the undefined 6xx series variable |
Modify program, put right |
| E405 | Variable data r4x0 error |
llegally used the undefined r4xx series variable |
Modify program, put right |
| E406 | r4003 can't be written |
The llegal witten operation is made to variable r4003(spindle realtime speed) |
Modify program, put right |
| E407 | r4007 can't be written |
The llegal witten operation is made to variable r4007(spindle real-time speed) |
Modity program, put right |
| 274 | |||
| Alarm number |
Alarm prompt | Alarm reason | Troubleshooting |
| E408 | r4008 can't be written |
The llegal witten operation is made to variable r4008(spindle real-time speed) |
Modify program, put night |
| E409 | Not assign a value to r6xxx in monitor |
The condition statement in process monitor evaluates the r6xxx series variable |
Modify program, put night |
| E410 | r711x Invalid data |
Write the undefined valuetor711x series vaniable |
Modify program, put night |
| E411 | r4002 can't be witten |
Witen operation is made to the read only machining time variable 4002 |
Modify program, put right |
| E412 | The variable doesn't support this kind of operation |
The system nonsupported operator is used in the assignment statement |
Modify program, put night |
| E413 | The unknown process monitor description |
The system nonsupported judgment condition is used in the statement of process monitor descniption |
Modify program, put right |
| E414 | Unknown pointer variable |
The pointer variable points to the non-common vanable or the exceeded range pointer variableis used |
Modify program, put right |
| E415 | The variable r4004 can't be witten |
Making witten operation to reading variable r4004 |
Modify program, put right |
| E416 | The vaniable r4012 can't be witten |
Making witten operation to reading variable r4012 |
Modify program, put night |
